H-1135 Tub Grinder

Standard Features

• The H-1135 has 12” diameter x 4’ long dual augers for discharging ground product. Augers are mounted with two heavy-duty bearings located at the base of the discharge allowing free flow of product to the stacking conveyor. Expansion of the discharge area allows for higher capacity and reduces possibility for plugging.
• On the H-1135, the tub rotation feeds the hammermill using a Wachendorf Electronic Control Governor, which stabilizes engine load by adjusting or stopping the tub speed. It also controls tub direction, clockwise, stop, and counter-clockwise as well as tracking total grinding hours and job hours.
• The newly designed drive system was updated for easier service and maintenance of the H-1135. The drive allows for a much smoother running grinder.
• The belt drive system for the hammermill has 8-5 VP belts to handle the increased rotor speed and increased horsepower capacity. The spring tension belt drive automatically adjusts belt tension as the belts stretch.
• Grain grinding with a Haybuster PTO tub grinder has become a very popular use of our hay grinding machines. Installing a grain grinding hopper on the hammermill and changing screens will convert the H-1135 into a high-capacity grain grinder.
• The H-1135’s tub opens a full 90 degrees for easy access to the hammermill and drive train for maintenance and service.
• Heavy Duty Axle Transport System 445/50R x 22.5 Super Single Tires 16.1 x W14C, 8 bolt rims with 6” pilot hole. Tapered Bearing System.
• The hydraulic folding 24” wide by 26’ long high-capacity stacking conveyor is designed for the increased capacity of the H-1135. It can stack material 18’ 6” high.
• The Big Bite 50” heavy-duty hammermill is now standard equipment and is located at the rear of the tub to reduce the length of the discharge. This, along with the increased area around and under the screens accelerates product discharge and reduces the potential of plugging. The heavy-duty hammermill operates at 2140 rpm and is constructed with 88 forged swinging hammers. The hammers are hardened and are held in place with 1 ¼” case-hardened hammer rods. The hammermill is mounted on a 3 ½” stress-proof shaft supported by 3 ¼” bearings.
• Heavy duty bolt in 9 bar mill grate allows operator the ability to remove and add bars as grinding conditions change.
• Controls tub forward, stop, reverse and speed. Controls conveyor raise and lower.

Optional Features

PTO Shaft -1000 RPM
Tractor Half, 1-3/4 in, 20 Spline Shaft
Tractor Half, 1-3/8 in, 21 Spline Shaft

Hammermill Feeding

Slug Buster, 5 tooth screen hold down Bolt in Mill grate/slug bar for grinding tough hay or crop residue.

Geyser Plates
Geyser Plate Kit, use with the Slug Buster
Geyser Plate Kit, slotted, use with the Mill Grate

Hopper for Grain Grinding

Ear Corn Kit
Better diets for dairy cows - an article from the USDA - describes how finely ground grains/corn can offer a better diet for cows.

Closed Center Conversion Kit
This kit is required to operate the conveyor lift valve properly with John Deere 60 and older series tractors.

Grinding Screens
1/8" (3.18 mm) Round Hole Screen Half*
3/16" (4.76 mm) Round Hole Screen Half**
1/4" (6.35 mm) Round Hole Screen Half
3/8" (9.52 mm) Round Hole Screen Half
1/2" (12.7 mm) Round Hole Screen Half
5/8" (15.88 mm) Round Hole Screen Half
3/4" (19.05 mm) Round Hole Screen Half
1" (25.4 mm) Round Hole Screen Half
1 1/2" (38.1 mm) Round Hole Screen Half
2" (50.8 mm) Round Hole Screen Half
3" (7.62 cm) Round Hole, Screen Half (standard)
4" (10.16 cm) Round Hole, Screen Half (standard)
5" (12.70 cm) Round Hole, Screen Half (standard)
6" (15.24 cm) Round Hole, Screen Half (standard)
7" (17.78 cm) Round Hole, Screen Half (standard)
8" (20.32 cm) Round Hole, Screen Half (standard)
Dummy (Open) Screen Half

*1/8" (3.18 mm) thick, **3/16" (4.76 mm) thick, all other screens are 1/4" (6.35 mm) thick